Adherence Of Candida Albicans Research Articles

Enhancing Presurgical Infant Orthopedic Appliances: Characterization, Mechanics, and Biofilm Inhibition of a Novel Chlorhexidine-Halloysite Nanotube-Modified PMMA

Objectives. This in vitro study aimed to develop a novel nanocomposite acrylic resin with inherent antimicrobial properties. This study evaluated its effectiveness against microbial biofilm formation, while also assessing its physical and mechanical properties. Methods. Polymethylmethacrylate (PMMA) was modified with four different concentrations of chlorhexidine halloysite nanotubes (CHX-HNTs): 1%, 1.5%, 3%, and 4.5 wt.% by weight, along with a control group (0 wt.% CHX-HNTs). The biofilm inhibition ability of the modified CHX-HNTs acrylic against Candida albicans, Staphylococcus aureus, Streptococcus pneumoniae, and Streptococcus agalactiae was assessed using microtiter biofilm test. In addition, ten samples from each group were then tested for flexural strength, surface roughness, and hardness. Statistical analysis was performed using one-way ANOVA and Tukey’s test for comparison (P<0.05). Results. CHX-HNTs effectively reduced the adhesion of Candida albicans and bacteria to the PMMA in a dose-dependent manner. The higher the concentration of CHX-HNTs, the greater the reduction in microbial adhesion, with the highest concentration (4.5 wt.%) showing the most significant effect with inhibition rates ≥98%. The addition of CHX-HNTs at any tested concentration (1%, 1.5%, 3%, and 4.5 wt.%) did not cause any statistically significant difference in the flexural strength, surface roughness, or hardness of the PMMA compared to the control group. Conclusions. The novel integration of CHX-HNT fillers shows promising results as an effective biofilm inhibitor on acrylic appliances. This new approach has the potential to successfully control infectious diseases without negatively affecting the mechanical properties of the acrylic resin. Clinical Relevance. The integration of CHX-HNTs into presurgical infant orthopedic appliances should be thoroughly assessed as a promising preventive measure to mitigate microbial infections. This evaluation holds significant potential for controlling infectious diseases among infants with cleft lip and palate, thereby offering a valuable contribution to their overall well-being.

Comparative Evaluation of Candida Albicans Adherence, Flexural strength and Water Sorption of Orthodontic Self-Cure Acrylic Resin Modified with 2-Methacryloyloxyethyl Phosphorylcholine by Two Different Techniques: in-vitro Study

Comparative Evaluation of Candida Albicans Adherence, Flexural strength and Water Sorption of Orthodontic Self-Cure Acrylic Resin Modified with 2-Methacryloyloxyethyl Phosphorylcholine by Two Different Techniques: in-vitro Study

Adhesion of Candida Albicans to digital versus conventional acrylic resins: a systematic review and meta-analysis

BackgroundThe present systematic review and meta-analysis investigated the available evidence about the adherence of Candida Albicans to the digitally-fabricated acrylic resins (both milled and 3D-printed) compared to the conventional heat-polymerized acrylic resins.MethodsThis study followed the guidelines of the Preferred Reporting Items for Systematic Review and Meta-analyses (PRISMA). A comprehensive search of online databases/search tools (Web of Science, Scopus, PubMed, Ovid, and Google Scholar) was conducted for all relevant studies published up until May 29, 2023. Only in-vitro studies comparing the adherence of Candida albicans to the digital and conventional acrylic resins were included. The quantitative analyses were performed using RevMan v5.3 software.ResultsFourteen studies were included, 11 of which were meta-analyzed based on Colony Forming Unit (CFU) and Optical Density (OD) outcome measures. The pooled data revealed significantly lower candida colonization on the milled digitally-fabricated compared to the heat-polymerized conventionally-fabricated acrylic resin materials (MD = − 0.36; 95%CI = − 0.69, − 0.03; P = 0.03 and MD = − 0.04; 95%CI = − 0.06, − 0.01; P = 0.0008; as measured by CFU and OD respectively). However, no differences were found in the adhesion of Candida albicans between the 3D-printed digitally-fabricated compared to the heat-polymerized conventionally-fabricated acrylic resin materials (CFU: P = 0.11, and OD: P = 0.20).ConclusionThe available evidence suggests that candida is less likely to adhere to the milled digitally-fabricated acrylic resins compared to the conventional ones.

Influence of post-processing on the adhesion of dual-species biofilm on polylactic acid obtained by additive manufacturing

IntroductionPost-processing (PP) is performed to improve the surface, which can favor microbial adhesion and consequent pathological manifestations that impair the indication of polylactic acid (PLA) obtained by fused filament fabrication (FFF) for biomedical applications. This aims to evaluate the influence of chemical, thermal, and mechanical PP on the adhesion of Streptococcus mutants and Candida albicans, roughness, and wettability of the PLA obtained by FFF with and without thermal aging. MethodsThe specimens were designed in the 3D modeling program and printed. The chemical PP was performed by immersion in chloroform, the thermal by the annealing method, and the mechanical by polishing. Thermal aging was performed by alternating the temperature from 5 °C to 55 °C with 5000 cycles. Colony-forming unit (CFU/mL) counting was performed on dual-species biofilm of C. albicans and S. mutans. Roughness was analyzed by rugosimeter and wettability by the sessile drop technique. Data were verified for normality using the Shapiro-Wilk test, two-way ANOVA (α = 0.05) applied for CFU and wettability, and Kruskal-Wallis (α = 0.05) for roughness. ResultsChemical, thermal, and mechanical PP methods showed no influence on CFU/mL of C. albicans (p = 0.296) and S. mutans (p = 0.055). Thermal aging did not influence microbial adhesion. Chemical PP had lower roughness, which had increased after aging. Wettability of the mechanical PP was lower. ConclusionsPost-processing techniques, do not present an influence on the adhesion of S. mutans and C. albicans in PLA obtained by FFF, chemical PP reduced roughness, and mechanical reduced wettability. Thermal aging did not alter the microbial adhesion and altered the roughness and wettability.

The influence of salivary pH on the adhesion of Candida to acrylic prosthetic materials obtained using conventional and digital techniques

The influence of saliva pH on the adhesion of Candida albicans to PMMA-based prosthetic materials manufactured using conventional and digital techniques (3D printing, milling) was examined. The obtained data were subjected to statistical analysis using one-way ANOVA and the Tukey HSD post hoc test (a = 0.05). Materials obtained by 3D printing had the highest surface roughness, while those obtained conventionally had the highest number of CFU (colony-forming unit). The mean CFU value was highest at pH 4.5 and statistically significant compared to other pH values. No significant correlation was found between surface roughness and the average CFU value. The surface of materials obtained using the conventional and milling methods showed lower adhesion of Candida albicans.

Effect of denture base acrylic resin containing silver nanoparticles on Candida Albicans adhesion and its release in artificial saliva

Background Candida albicans was considered a main reason of precipitate formations and decomposition of acrylic denture base; so many trials were objected to resist this microbial action and prolong the shelf life of the formulated fitting base. Aim of the work The present study aimed to adopt a new mixture of the silver nanoparticles with the PMMA denture base to get a prolonged antimicrobial protection for the formed base against Candida albicans. Statement of problem Accumulation of Candida Albicans on fitting surface of poly methyl meth-acrylate (PMMA) denture base. Purpose To evaluate the effect of denture base acrylic resin containing silver Nanoparticles (Ag NP) on Candida Albicans adhesion and its release in artificial saliva. Materials and methods Sixty round disks with dimensions of 15 mm diameter and 3 mm thickness specimens were prepared for this research. Control group A: 10 specimens were prepared from pure PMMA. Experimental group B: 50 specimens were prepared from PMMA containing 5% of Ag NP. Isolation and identification of Candida Albicans were taken from oral cavity of 10 patients by swabbing. The Specimens were immersed in artificial saliva for 3, 6, and 9 months. Microbiological test was done for specimens of each group to detect Candida Albicans accumulation at the same interval period by measuring the inhibition zone created around the disks. Specimens were taken from the artificial saliva to evaluate silver release in it by using UV-Vis Spectrophotometer Instrument ‘SHIMADZO UV-310 PC. For Spectrophotometer 1.0 cm and/or 0.2 cm matched silica cells. The amount of accumulated silver released was calculated to detect its cytotoxic effect1. Results For control group A there was no inhibition zone for Candida growth around the specimens. While for group B with Ag NP the greatest antimicrobial effect was found at zero time then was decreased gradually with increasing the time till reaching zero effect after 9 months resembling the control group. The amount of Nano silver in artificial saliva after 3 months was found to be little then it was increased gradually with increasing time. Conclusion Adding Ag NP to PMMA denture base has antimicrobial effect against Candida Albicans for only 9 months; then there was no effect as silver was released in saliva. The amount of released silver was found to be with no cytotoxic effect.

An in Vitro Study on Comparative Adherence of Oral Candida Albicans and Non–albicans Candida to Human Buccal Epithelial Cells and Its Antifungal Susceptibility Pattern

An in Vitro Study on Comparative Adherence of Oral Candida Albicans and Non–albicans Candida to Human Buccal Epithelial Cells and Its Antifungal Susceptibility Pattern

Evaluation of surface energy and surface stability and adherence of Candida albicans to octa fluoro pentyl (meth) acrylate-coated PEEK using plasma spray

ABSTRACT Background: Polyetheretherketone (PEEK) has favorable properties that make it able to be used as a denture base material, but it is also susceptible to the adhesion of microorganisms. In this study, we applied Octafluoropentyl (meth) acrylate (OFPA) coating on the PEEK polymer surface by using plasma spray and investigated the functional groups present on the surface, changes in the surface energy and Candida albicans adhesion. Materials and Methods: In this experimental study, the samples were placed in a control group without surface preparation and three experimental groups that were subjected to plasma spray for 10, 30, and 60 s and then impregnated with degassed Octa fluoropentyl (meth) acrylate (Sigma-Aldrich, USA) monomer. Fourier transform infrared spectroscopy (FTIR) was used to identify the functional groups and new chemical bonds between PEEK and OFPA, and Sessile Drop Method was used to evaluate the surface’s wettability. The surface morphology was checked using a LEXT OLS4000 (Olympus®-Japan) microscope, and the inhibition of C. albicans adhesion was also checked by counting the colonies in terms of colony forming unit/mL (CFU/mL). Kurskal–Wallis analysis was conducted to assess Candida adhesion, while wettability was evaluated using analysis of variance and post hoc analyses. The level of statistical significance was set at P < 0.05. Results: FTIR analysis confirmed that a chemical between OFPA and PEEK was established. The samples showed a significant increase in the contact angle after 30 s of plasma application (CA = 88.2 ± 7.3). The contact angle decreased again by increasing the surface modification to 60 s (CA = 64.33 ± 5.5). Examining the surface morphology of the samples shows an increase in surface roughness with increasing plasma time up to 60 s. The number of adherent colonies was the lowest in 30 s group, but it was not statistically significant (P = 0.658). Conclusion: No statistically significant difference in C. albicans CFU/mL count was found between groups. The contact angle of the 30 s group was significantly higher than the control group.

Клиническое значение интегральной регистрации маркеров эндотоксического иммунитета и колонизационной резистентности буккальных эпителиоцитов при рецидивирующем бронхите у подростков

Recurrent bronchitis (RB) occupies one of the key places in the structure of nonspecific diseases of the respiratory tract and remains a significant medical and social problem in healthcare. The purpose — to investigate and evaluate the clinical significance of integral registration of markers of endotoxic immunity and colonization resistance of buccal epithelial cells (BE) in RB in adolescents. Material and methods. The study included 117 children (12–17 years old), including 78 with RB — the main group, 29 with acute bronchitis (AB) — the comparison group and 23 conditionally healthy children — the control group. The analysis of anamnestic, clinical, paraclinical data, verification of etiologically significant viruses, registration of artificial colonization of buccal epithelial cells (BE), colonization index (CI), micro-LAL test were carried out. Statistical processing of the results was carried out using the SPSS program. Results. A significant difference in markers of colonization resistance and anti-endotoxin protection was revealed in recurrent inflammation in the respiratory tract in comparison with AB in peers. In RB, the initial degree of Candida albicans adhesion to BE was significantly higher in relation to AB (p = 0.0427) and upon discharge from the hospital did not reach normative values, being significantly different from patients with AB (p = 0.0391). The high index of artificial colonization indicates the activation of allochthonous flora and disruption of the microbiota in the oral cavity, which negatively affects the body reactivity. In patients with RB, the titer of antiglycolipid antibodies significantly decreased and in 75% the values did not return to normal, while in AB they did not differ from the control. High levels of endotoxin were noted in RB compared to AB (p = 0.0317). Such patients were diagnosed with a more severe course of the disease with symptoms of endogenous intoxication and a long hospitalization period. Using the method of correlation analysis, a high direct relationship was established between artificial colonization and endotoxin concentration (r = 0.71). The relationship between these parameters in AB was significantly less pronounced (r = 0.3). The results obtained indicate close integration and mutual modulation of the local oral immunity and antiendotoxin defense. Conclusion. Integral registration of the markers of reactivity of specific anti-endotoxin immunity and colonization resistance reflect the severe inflammatory process in the respiratory tract and predict the risk of a chronic pathological process in the bronchopulmonary system.

Flexural strength, surface roughness, and biofilm formation of ceramic-reinforced PEEK: An in vitro comparative study.

This in vitro study aimed to compare flexural strength, surface roughness, and biofilm formation of ceramic-reinforced PEEK with conventionally heat-compressed and milled polymethylmethacrylate (PMMA) denture base materials. Thirty strips (6.4×10×3 mm) and 30 discs (10×1 mm) were fabricated from a heat-compressed PMMA, milled PMMA, and ceramic-reinforced PEEK, 10 each. One surface of each sample was polished to mimic the laboratory procedure for denture base materials. Strips were then subjected to a 3-point bend test using a universal testing machine at a crosshead speed of 5.0 mm/min. An optical profilometer was used to assess the Ra value (mm) of the discs on polished and unpolished sides. Biofilm formation behavior was analyzed by measuring the colony-forming unit (CFU)/ml of Candida albicans on the unpolished surface of the discs. One-way ANOVA followed by Tukey multiple comparison tests were used to compare the flexural strength, Ra value, and biofilm formation of the studied materials (a = 0.05). Ceramic-reinforced PEEK showed significantly higher flexural strength (178.2 ±3.2 MPa) than milled PMMA (89.6 ±0.8 MPa; P<0.001) and heat-compressed PMMA (67.3 ±5.3 MPa; P<0.001). Ceramic-reinforced PEEK exhibited a significantly higher Ra value than the other groups on unpolished sides; however, the polishing process significantly reduced the Ra values of all studied groups (P<0.05). There was no significant difference in Candida albicans adhesion among the groups (P<0.05). The flexural strength of tested materials was within acceptable limits for clinical use as a denture base material. Ceramic-reinforced PEEK had the highest surface roughness; however, its similarity in biofilm formation to other groups indicates its clinical acceptability as denture base material. This article is protected by copyright. All rights reserved.

Effect of tea tree oil on candida adherence and surface roughness of heat cure acrylic resin

Background: Denture cleansing was an important step that could prevent the spread of infection and improve a patient's health, the durability of the dentures, and the overall quality of life; therefore, it was necessary to choose a suitable cleanser that, in addition to being effective, did not have an unfavorable effect on the qualities of the denture base resin itself when used for an extended period. For this purpose, this study aimed to evaluate the effect of tea tree oil (TTO) on Candida albicans adhesion and the surface roughness property of poly(methyl methacrylate) denture material after immersion in TTO. Methods: A total of 55 heat-cured acrylic resin specimens were used for C. albicans adherence and surface roughness tests. They were distributed into groups (0.25%, 0.5%, 0.75%, and 1%) of TTO, distilled water (DW), and 2% clorhexidine digluconate, totaling five specimens for each group. The specimens were immersed in accordance with their group for 10 minutes. Surface roughness was determined by a profilometer, and C. albicans adherence was determined by measuring optical density with a spectrophotometer. For comparisons between groups for surface roughness and disinfection tests, one-way ANOVA was performed on SPSS program, considering α = 0.05. Results: TTO had a statistically significant effect on C. albicans adhesion to heat-cured acrylic resin (P &lt; 0.05) compared with negative control. Meanwhile, no statistically significant difference was found between 0.75% and 1% TTO concentrations (P &gt; 0.05), whereas the surface roughness test showed a statistically non-significant difference between TTO concentrations and DW (P &gt; 0.05). Conclusions: Immersion of acrylic resin in TTO was effective in decreasing C. albicans adhesion to it, and the greatest decrease was obtained by 1% TTO. The surface roughness test showed a non-significant difference in acrylic roughness after immersion in TTO.

In Vitro Evaluation of Candida albicans Adhesion and Related Surface Properties of CAD/CAM Denture Base Resins

In Vitro Evaluation of Candida albicans Adhesion and Related Surface Properties of CAD/CAM Denture Base Resins

Impact of chitosan-incorporated toothpaste on roughness, gloss, and antifungal potential of acrylic resin

This study aimed to test the efficacy of different silica-based toothpastes with or without chitosan, as a method of cleaning the acrylic surfaces of denture prostheses. Acrylic resin specimens were prepared to evaluate surface roughness and gloss (n = 10), and Candida albicans adhesion/inhibition (n = 2). Two toothpastes with different degrees of abrasiveness were used: Colgate (CT) and Elmex (EX), with or without 0.5% chitosan (Ch) microparticles (CTCh or EXCh, respectively). The negative control was brushed with distilled water. Brushing was simulated with a machine. Surface roughness and gloss were analyzed before and after brushing. Candida albicans incidence/inhibition was tested qualitatively to determine the acrylic resin antifungal activity. The roughness and gloss data were analyzed with a generalized linear model, and the Kruskal Wallis and Dunn tests, respectively (α = 5%). Brushing with toothpastes increased roughness and reduced gloss, compared with the negative control (p < 0.05). CT showed a more significantly different change in roughness and gloss, in relation to the other groups (p < 0.05). Addition of chitosan to CT reduced its abrasive potential, and yielded results similar to those of EX and EXCh. Specimens brushed with CT showed a higher potential for Candida albicans adherence, despite its higher antifungal action. Addition of chitosan to the toothpaste made both toothpaste and brushing more effective in inhibiting Candida albicans. CT had the potential to increase roughness, reduce gloss, and increase Candida albicans adherence. In contrast, chitosan added to CT showed greater antifungal potential, and a higher synergistic effect than EX.

Candida albicans Adhesion Measured by Optical Nanomotion Detection

Cellular adhesion plays an important role in numerous fundamental physiological and pathological processes. Its measurement is relatively complex, requires sophisticated equipment, and, in most cases, cannot be carried out without breaking the links between the studied cell and its target. In this contribution, we propose a novel, nanomotion-based, technique that overcomes these drawbacks. The applied force is generated by the studied cell itself (nanomotion), whereas cellular movements are detected by traditional optical microscopy and dedicated software. The measurement is non-destructive, single-cell sensitive, and permits following the evolution of the adhesion as a function of time. We applied the technique on different strains of the fungal pathogen Candida albicans on a fibronectin-coated surface. We demonstrated that this novel approach can significantly simplify, accelerate, and make more affordable living cells–substrate adhesion measurements.

Colonization resistance of buccal epitheliocytes as an indicator of mucosal immune homeostatic resources in children with recurrent respiratory diseases

Of particular interest is the study of colonization resistance of the oral cavity as a physiological phenomenon that reflects the ability of the microbiota and macroorganism in cooperation to protect the ecosystem of the oral cavity from pathogens. Purpose is to evaluate the significance of indicators of colonization resistance of buccal epithelial cells as a marker of homeostatic resources of mucosal immunity in recurrent respiratory diseases in children. Material and methods. 232 (5–16 years old) children were examined, including 56 children with acute bronchitis, 73 with recurrent bronchitis, 103 with community-acquired pneumonia. The control group included 31 apparently healthy children of the same age and sex. Used: conventional paraclinical and laboratory-instrumental methods, etiological verification of viruses and bacteria, colonization index and artificial colonization of buccal epitheliocytes, antiadhesive activity of saliva. Results. 64.38% of children with recurrent bronchitis and 72.82% of children with community-acquired pneumonia were born from an aggravated pregnancy and already at 3 months had signs of acute respiratory diseases. Viral antigens were detected in 63.36% of children. An inverse relationship was found between the indicators of artificial colonization and adhesion of Candida albicans on buccal epithelial cells — the lower the values of artificial colonization, the more often pneumonia and recurrent bronchitis were recorded. A significant decrease in saliva antiadhesion was found in recurrent bronchitis and community-acquired pneumonia, significantly different not only from the control, but also from patients with acute bronchitis. This contingent of patients finds itself in extremely unfavorable conditions due to the disruption of the adaptive reserves of the mucosal defense of the body. Conclusion. A decrease in the index of colonization, antiadhesive activity of saliva against the background of increasing parameters of artificial colonization in children with recurrent bronchitis and community-acquired pneumonia indicate deep dysbiosis. The high significance of screening approaches in assessing the homeostatic resources of mucosal protection of the oral cavity in children with bronchopulmonary pathology has been proven.

Comparative Evaluation of Surface Roughness and Adhesion of Candida albicans on Conventional Heat-cured, Injection-molded Thermoplastic Resin and CAD-CAM Denture Base Resin as Affected by Denture Cleanser: An In Vitro Study

Comparative Evaluation of Surface Roughness and Adhesion of Candida albicans on Conventional Heat-cured, Injection-molded Thermoplastic Resin and CAD-CAM Denture Base Resin as Affected by Denture Cleanser: An In Vitro Study

Konvansiyonel, CAD/CAM frezeleme ve 3D baskı yöntemleriyle üretilmiş geçici materyallerin yüzey özelliklerinin Streptococcus mutans ve Candida albicans tutunumuna etkileri

Objectives: The purpose of this in vitro study was to compare conventionally manufactured, CAD/CAM milled, and 3D-printed interim materials based on their susceptibility to adherence of Streptococcus mutans and Candida albicans, and examine the influence of surface roughness and hydrophobicity. Materials and Methods: Eighty disc-shaped specimens fabricated from autopolymerized polymethyl methacrylate (A-PMMA), bis-acryl composite (Bis-acrylate), CAD/CAM PMMA-based polymer (Milled-PMMA), and 3D-printed resin (Printed) were subjected to 10,000 thermal cycles (5-55 °C) and divided into two groups (n=10) according to microbial suspension used: Streptococcus mutans and Candida albicans. Surface roughness (Ra) and hydrophobicity (WCA) of specimens were measured. An adhesion test was performed by incubating the specimens in Streptococcus mutans and Candida albicans suspensions at 37 °C for 24 hours, and the adherent cells were evaluated by counting colony-forming units (CFU/ml). Scanning electron microscopy (SEM) was performed to analyze the surfaces (n=2). Data were analyzed with Kruskal-Wallis and Mann-Whitney U tests. Spearman’s correlation analysis was used to determine correlation among the measurements (α=.05). Results: Type of restorative material significantly influenced Ra and WCA. The highest adhesion of Streptococcus mutans was observed in Printed, followed by Bis-acrylate, A-PMMA, and Milled-PMMA (p=.001). The highest adhesion of Candida albicans was noted on A-PMMA, followed by Printed, Bis-acrylate, and Milled-PMMA (r=.001). The adhesion of Streptococcus mutans (r=.660) and Candida albicans (r=.413) showed a positive correlation with Ra. A negative correlation was found between WCA of the materials and Streptococcus mutans adhesion (r=-.373). Conclusions: Surface roughness plays an important role in the adherence of microorganisms. CAD/CAM PMMA-based polymers may be a better choice to reduce microbial adhesion in long-term use.

The influence of lemongrass essential oil addition into heat cured acrylic resin against Candida albicans adhesion

Background: For decades, the use of naturally accessible materials in treating human disease has been widespread. The goal of this study was to determine the anti-fungal effectiveness /of the lemongrass essential oil (LGEO) versus Candida albicans (C. albicans) adhesion to polymethylmethacrylate (PMMA) materials. Material and methods: LGEO's anti-fungal activity was tested against C. albicans adhesion using the following concentration of LGEO in PMMA monomer (2.5 vol. %, 5 vol. % LGEO) selected from the pilot study as the best two effective concentrations. A total of 40 specimens were fabricated for the candida adherence test and were subdivided into four equal groups: negative control 0 vol. % addition, experimental with 2.5 vol. % and 5 vol. % of LGEO addition and positive control with 1.4 wt. % nystatin addition. The sterile PMMA specimens were incubated at room temperature for 1 hr in sterile tubes with a sabouraud dextrose broth (SDA) in which a small amount of the yeast was isolated and suspended; under the inverted light microscope, the examination was done. The data were evaluated using a one-way ANOVA test, which showed a significant result at p&lt; 0.05. Results: The findings of the C. albicans adherence test exposed a considerable reduction in the number of C. albicans cells adhering to PMMA after adding 2.5 vol. % and 5 vol. % LGEO compared to specimens from the negative control and positive control groups at p&lt; 0.05. Conclusion: Adding LGEO into a heat-cure acrylic material can result in a denture base material with anti-fungal properties versus C. albicans microorganisms. The experimental group 5 vol. % LGEO additive showed the best anti-fungal activity

Oral microbial colonization on titanium and polyetheretherketone dental implant healing abutments: An in vitro and in vivo study

Although polyetheretherketone (PEEK) implant healing abutments have become popular because of their esthetic, mechanical, and chemical properties, studies analyzing oral polymicrobial adhesion to PEEK abutments are lacking. The purpose of this in vitro and in vivo study was to evaluate oral microbial adhesion and colonization on titanium (Ti) and PEEK healing abutments. Ti (N=35) and PEEK substrates (N=35) were evaluated in vitro in terms of the initial adhesion (1 hour) or biofilm accumulation (48 hours) of Candida albicans and a polymicrobial inoculum using stimulated human saliva to mimic a diverse oral microbiome. Surface decontamination ability was evaluated after 24 hours of in vitro biofilm formation after exposure to an erbium-doped yttrium aluminum garnet (Er:YAG) laser. Conventional and flowable composite resin veneering on PEEK was also tested for microbial adhesion. In addition, an in vivo model with 3 healthy volunteers was conducted by using a palatal appliance containing the tested materials (3 or 4 specimens of each material per appliance) for 2 days to evaluate the effect of substrate on the microbial profile. Biofilms were evaluated by live cell counts and scanning electron microscopy images, and the microbial profile by Checkerboard deoxyribonucleic acid (DNA)-DNA hybridization. The t test and Mann-Whitney test were used to compare the groups (α=.05). PEEK and Ti materials showed similar fungal adhesion (P>.05). Although the PEEK surface limited the initial in vitro polymicrobial adhesion (approximately 2 times less) compared with Ti (P=.040), after 48 hours of biofilm accumulation, the microbial load was statistically similar (P=.209). Er:YAG laser decontamination was more effective on PEEK than on Ti surfaces, reducing approximately 11 times more microbial accumulation (P=.019). Both composite resins tested showed similar microbial adhesion (1 hour). In vivo, the PEEK material showed reduced levels of 6 bacterial species (P<.05), including the putative pathogen Treponema denticola. Although PEEK and Ti had similar bacterial and fungus biofilm attachment and accumulation, PEEK promoted a host-compatible microbial profile with a significantly reduced T. denticola load.

In Vitro Evaluation of Candida albicans Adhesion on Heat-Cured Resin-Based Dental Composites.

Microbial adhesion on dental restorative materials may jeopardize the restorative treatment long-term outcome. The goal of this in vitro study was to assess Candida albicans capability to adhere and form a biofilm on the surface of heat-cured dental composites having different formulations but subjected to identical surface treatments and polymerization protocols. Three commercially available composites were evaluated: GrandioSO (GR), Venus Diamond (VD) and Enamel Plus HRi Biofunction (BF). Cylindrical specimens were prepared for quantitative determination of C. albicans S5 planktonic CFU count, sessile cells CFU count and biomass optical density (OD570 nm). Qualitative Concanavalin-A assays (for extracellular polymeric substances of a biofilm matrix) and Scanning Electron Microscope (SEM) analyses (for the morphology of sessile colonies) were also performed. Focusing on planktonic CFU count, a slight but not significant reduction was observed with VD as compared to GR. Regarding sessile cells CFU count and biomass OD570 nm, a significant increase was observed for VD compared to GR and BF. Concanavalin-A assays and SEM analyses confirmed the quantitative results. Different formulations of commercially available resin composites may differently interact with C. albicans. The present results showed a relatively more pronounced antiadhesive effect for BF and GR, with a reduction in sessile cells CFU count and biomass quantification.